CVE-2026-23005

In the Linux kernel, the following vulnerability has been resolved:

x86/fpu: Clear XSTATE_BV[i] in guest XSAVE state whenever XFD[i]=1

When loading guest XSAVE state via KVM_SET_XSAVE, and when updating XFD in
response to a guest WRMSR, clear XFD-disabled features in the saved (or to
be restored) XSTATE_BV to ensure KVM doesn't attempt to load state for
features that are disabled via the guest's XFD.  Because the kernel
executes XRSTOR with the guest's XFD, saving XSTATE_BV[i]=1 with XFD[i]=1
will cause XRSTOR to #NM and panic the kernel.

E.g. if fpu_update_guest_xfd() sets XFD without clearing XSTATE_BV:

  ------------[ cut here ]------------
  WARNING: arch/x86/kernel/traps.c:1524 at exc_device_not_available+0x101/0x110, CPU#29: amx_test/848
  Modules linked in: kvm_intel kvm irqbypass
  CPU: 29 UID: 1000 PID: 848 Comm: amx_test Not tainted 6.19.0-rc2-ffa07f7fd437-x86_amx_nm_xfd_non_init-vm #171 NONE
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
  RIP: 0010:exc_device_not_available+0x101/0x110
  Call Trace:
   <TASK>
   asm_exc_device_not_available+0x1a/0x20
  RIP: 0010:restore_fpregs_from_fpstate+0x36/0x90
   switch_fpu_return+0x4a/0xb0
   kvm_arch_vcpu_ioctl_run+0x1245/0x1e40 [kvm]
   kvm_vcpu_ioctl+0x2c3/0x8f0 [kvm]
   __x64_sys_ioctl+0x8f/0xd0
   do_syscall_64+0x62/0x940
   entry_SYSCALL_64_after_hwframe+0x4b/0x53
   </TASK>
  ---[ end trace 0000000000000000 ]---

This can happen if the guest executes WRMSR(MSR_IA32_XFD) to set XFD[18] = 1,
and a host IRQ triggers kernel_fpu_begin() prior to the vmexit handler's
call to fpu_update_guest_xfd().

and if userspace stuffs XSTATE_BV[i]=1 via KVM_SET_XSAVE:

  ------------[ cut here ]------------
  WARNING: arch/x86/kernel/traps.c:1524 at exc_device_not_available+0x101/0x110, CPU#14: amx_test/867
  Modules linked in: kvm_intel kvm irqbypass
  CPU: 14 UID: 1000 PID: 867 Comm: amx_test Not tainted 6.19.0-rc2-2dace9faccd6-x86_amx_nm_xfd_non_init-vm #168 NONE
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
  RIP: 0010:exc_device_not_available+0x101/0x110
  Call Trace:
   <TASK>
   asm_exc_device_not_available+0x1a/0x20
  RIP: 0010:restore_fpregs_from_fpstate+0x36/0x90
   fpu_swap_kvm_fpstate+0x6b/0x120
   kvm_load_guest_fpu+0x30/0x80 [kvm]
   kvm_arch_vcpu_ioctl_run+0x85/0x1e40 [kvm]
   kvm_vcpu_ioctl+0x2c3/0x8f0 [kvm]
   __x64_sys_ioctl+0x8f/0xd0
   do_syscall_64+0x62/0x940
   entry_SYSCALL_64_after_hwframe+0x4b/0x53
   </TASK>
  ---[ end trace 0000000000000000 ]---

The new behavior is consistent with the AMX architecture.  Per Intel's SDM,
XSAVE saves XSTATE_BV as '0' for components that are disabled via XFD
(and non-compacted XSAVE saves the initial configuration of the state
component):

  If XSAVE, XSAVEC, XSAVEOPT, or XSAVES is saving the state component i,
  the instruction does not generate #NM when XCR0[i] = IA32_XFD[i] = 1;
  instead, it operates as if XINUSE[i] = 0 (and the state component was
  in its initial state): it saves bit i of XSTATE_BV field of the XSAVE
  header as 0; in addition, XSAVE saves the initial configuration of the
  state component (the other instructions do not save state component i).

Alternatively, KVM could always do XRSTOR with XFD=0, e.g. by using
a constant XFD based on the set of enabled features when XSAVEing for
a struct fpu_guest.  However, having XSTATE_BV[i]=1 for XFD-disabled
features can only happen in the above interrupt case, or in similar
scenarios involving preemption on preemptible kernels, because
fpu_swap_kvm_fpstate()'s call to save_fpregs_to_fpstate() saves the
outgoing FPU state with the current XFD; and that is (on all but the
first WRMSR to XFD) the guest XFD.

Therefore, XFD can only go out of sync with XSTATE_BV in the above
interrupt case, or in similar scenarios involving preemption on
preemptible kernels, and it we can consider it (de facto) part of KVM
ABI that KVM_GET_XSAVE returns XSTATE_BV[i]=0 for XFD-disabled features.

[Move clea
---truncated---